Skill Up. Step Forward.

At Wyoming Sugar, your development matters. From hands-on training and mentorship to support for continued education, we give you the tools to succeed. Over one in five team members advance their careers each year—because when you move forward, so do we.

Maintenance Technician IV - Welder - $24.48

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Must be able to listen & follow directions
  • Ability to read and use tape measure
  • Ability to receive instructions and clearly communicate project updates

Test Requirements:

  • Must be capable of fabricating 4”x 4” steel box ¼” thick utilizing MIG welder in position
  • Test box must be square and watertight

Tool List Requirements:

  • Tape measure
  • Combination Square
  • 2’ level
  • 2’ square
  • Torpedo level

Maintenance Technician III - Welder - $28.56

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employees keep their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Capable of layout, fabrication, & fit up of pipe
  • Make competent vertical & overhead welds in wet or dry conditions and positions
  • Must be willing & capable of following A/E system & contribute to their efficient closeout
  • Follow, read, record work orders via Asset Essentials electronically or print
  • Must possess all attributes on Maintenance Tech IV – Welder

Test Requirements:

  • Must pass 6G schedule 80 pipe bend test – stick
  • Must possess all attributes of Maintenance Tech IV – Welder

Tool List Requirements:

  • Chalk box
  • Plumb Bob
  • Welder’s Helmet
  • Possess all tools on Maintenance Tech IV – Welder list and be knowledgeable in their use

Maintenance Technician II - Welder - $31.62

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Capable of leading & motivating a crew
  • Willing to train subordinates
  • Ability to solve problems
  • Capable of taking direction from supervision including planning pipe routes, fabricating parts & pieces, making complete material lists used by purchasing
  • Capable of reading blueprints
  • Ability to navigate A/E computer program & actively contribute to its success
  • Must possess all attributes of Maintenance Tech IV & III – Welder
  • Follow, read, and record work orders via Asset Essentials electronically

Test Requirements:

  • Ability to electronically fulfill duties in A/E (document labor, parts, etc…)
  • Must pass all position, all thickness weld tests with MIG or pass 6G pipe bend test with TG
  • Must pass 3G plate bend test – MIG
  • Must pass destructive weld test

Tool List Requirements:

  • Laser level
  • 50’ Tape
  • Possess all tools on Maintenance Tech IV & III – Welder list and be knowledgeable in their use

Maintenance Technician I - Welder - $34.68

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Possess computer skills
  • Ability to generate and follow Asset Essentials preventive maintenance program
  • Initiate quote requests via e-mail and contract vendors for materials & supplies
  • Ability to step in to cover any welding position or task required to achieve a goal
  • Ability to direct multiple welding crews at one time
  • Must possess all attributes of Maintenance Tech II, III, & IV – Welder
  • Lead, follow, read and record work orders via Asset Essentials electronically
  • Record parts utilized, man hours per unit, and communicate information to supervisor

Test Requirements:

  • Must pass 6G pipe tests — both TIG & Stick
  • Must pass 3A plate test with MIG

Tool List Requirements:

  • 2 Hole Pins
  • Center Finder
  • Compass
  • Plumb Bobs
  • Possess all tools on Maintenance Tech IV, III, & II – Welder list and be knowledgeable on their use

Maintenance Technician IV - Mechanic - $22.44

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Possess a positive “can do attitude” and a willingness to work
  • Forklift certified
  • Basic knowledge of tools and equipment
  • Be familiar with protocols for checking tools and materials out of the storeroom correctly
  • Ability to receive instructions and clearly communicate project updates

Test Requirements:

  • Pass Forklift Certification
  • Capable of working at heights, in extreme heat or cold. Able to think logically
  • Pass valves rebuild course

Tool List Requirements:

  • Channel locks
  • Crescent wrench
  • Basic end wrench set — 1/4″ to 1 1/8”
  • Screwdriver
  • Flashlight
  • Tool bag

Maintenance Technician III - Mechanic - $25.50

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Ability to fulfill duties in AE (record work on hard copy of work order, list parts, etc…)
  • Ability to independently make rounds of the factory and report findings to supervision
  • Ability to identify and repair faulty bearings, seals, sheaves, belts, and replace them if necessary
  • Ability to align pumps and motors with laser alignment and belt hog tools
  • Must be able to rebuild/re-line valves and install correctly
  • Be familiar with station locations in the factory and be willing to work in heat, cold, wet, or dry conditions
  • Follow, read, record work orders via Asset Essentials electronically or print

Test Requirements:

  • Demonstrate understanding of work order process and complete paperwork
  • Demonstrate knowledge of areas of the factory and tools needed to complete work
  • Successfully repack pumps, change bearings, seals & belts satisfactory to supervisors
  • Align pumps and motors independently
  • Demonstrate reliability daily and have a maximum of one attendance point or less

Tool List Requirements:

  • Channel locks – multiple sizes
  • Crescent wrenches – multiple sizes
  • Flashlight
  • Tool bag
  • Allen wrenches
  • 14″ pipe wrench
  • 18″ pipe wrench
  • Tape measure
  • Hammers
  • Possess all tools on Maintenance Tech IV & III – Mechanic list and be knowledgeable in their use

Maintenance Technician II - Mechanic - $27.54

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Ability to electronically fulfill duties in AE (document labor, parts, etc.)
  • Ability to make basic welds and diagnose minor electrical issues
  • Willingness to attend & successfully complete gearbox repair/rebuild school with passing grades
  • Willingness to attend & successfully complete pump repair/rebuild school with passing grades
  • Follow, read, and record work orders via Asset Essentials electronically

Test Requirements:

  • Capable of installing centrifugal screens during campaign
  • Successfully troubleshoot & repair centrifugal during inter-campaign
  • Successfully troubleshoot & repair beet slicing equipment during inter-campaign

Tool List Requirements:

  • Complete socket set — 1 1/4″ to 1 1/2″
  • Complete set end wrenches — 15/16″ to 1 1/2″
  • Level
  • Toolbox
  • 36″ pipe wrench
  • 24″ pipe wrench
  • Dead blow hammer
  • 3/8″ drive Allen wrench set
  • Possess all tools on Maintenance Tech IV & III – Mechanic list and be knowledgeable in their use

Maintencance Technician I - Mechanic - $29.58

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Ability to conduct training courses for maintenance items (i.e. valves, etc.)
  • Ability to initiate work orders in A/E and assist supervisors in monitoring & updating preventive maintenance items
  • Successfully rebuild gearboxes and train subordinates in same
  • Successfully rebuild pumps and train subordinates in same
  • Possess all skills identified in Maintenance Tech IV through II – Mechanic positions
  • Lead, follow, read, and record work orders via Asset Essentials electronically
  • Record parts utilized, man hours per unit, and communicate information for supervisor

Test Requirements:

  • Capable of successfully rebuilding gearboxes
  • Capable of troubleshooting and repairing any type of pump utilized in the factory
  • Capable of troubleshooting and rebuilding any mechanical component in the factory and training others to perform the same
  • Participate in planning & scheduling of routine and emergency maintenance of all equipment
  • Willing and capable of leading teams for upcoming maintenance projects

Tool List Requirements:

  • Impact socket sets in Metric & English
  • Impact wrenches
  • Rigging tools: come-along, chain hoists, shackles
  • Measuring calipers
  • Seal drivers
  • Possess all tools on Maintenance Tech IV, III, & II – Mechanic list and be knowledgeable in their use

Maintenance Technician IV - Machinist - $24.48

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Ability to read micrometer and caliper sets
  • Machine a simple keyway in a shaft
  • Ability to receive instructions and clearly communicate project updates

Test Requirements:

  • Bore out a hub and breach a keyway layout, drill and tap

Tool List Requirements:

  • Toolbox
  • Calculator
  • Flashlight
  • Markers/pens
  • Tape measure at least 12”
  • 6” Caliper
  • 0”-1” & 1”-2” Micrometer
  • 1” Travel dial indicator with adjustable base .001 grad
  • Dial test indicator .0005
  • Mechanical edge finder
  • 6” scale 4R
  • Telescoping gage up to 6”
  • Thread/screw pitch gage (Standard and Metric)
  • Canter gage/fish tail
  • Hand file set (must have ALL handles)
  • Ball peen and dead blow hammer
  • Center punch set
  • Hand deburring tool
  • Allen wrench/hex key set (Standard and Metric)
  • Center drill set
  • Drill index (1/16” – 1/2”)

Maintenance Technician III - Machinist - $28.56

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Machine a Goulds pump shaft in a timely manner
  • Set up jobs in the mill and lathe in a timely manner
  • All skill requirements listed in Maintenance Tech IV – Machinist
  • Follow, read, record work orders via Asset Essentials electronically or print

Test Requirements:

  • Draw a print by hand
  • Complete tests required for Maintenance Tech IV – Machinist

Tool List Requirements:

  • Machinist Handbook
  • Machinist Square
  • Inside mic set
  • Depth mic set
  • Small tap handle
  • Torpedo level
  • Pick set
  • Prick/Spring punch
  • Parallel set
  • Feeler gage set
  • Scribe
  • Torx bit set (T1–T40)
  • Screwdriver set (Standard slot and Phillips)
  • Countersink 3/8” and ¾”
  • SAE and Metric wrench and socket set
  • 12” Crescent wrench
  • Possess all tools on Maintenance Tech IV – Machinist list and be knowledgeable in their use

Maintenance Technician II - Machinist - $31.62

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Efficient at machining manual machines
  • Knowledge of programming on CNC machines
  • Proven mechanical skills
  • Computer skills
  • Solicit quotes for parts and equipment from vendors
  • All skill requirements listed in Maintenance Tech IV and III – Machinist
  • Follow, read, and record work orders via Asset Essentials

Test Requirements:

  • Make a program on the CNC machine
  • Complete tests required for Maintenance Tech IV and III – Machinist

Tool List Requirements:

  • Spring caliper inside and outside
  • 12” caliper
  • 0-76” micrometer set
  • Radius Gage Set
  • Jack screw set
  • 12” combination square set
  • Snap ring pliers
  • Pry bar set
  • 10’ chain fall
  • Tool bag
  • Scraper set
  • Possess all tools on Maintenance Tech IV & III – Machinist list and be knowledgeable in their use

Maintenance Technician I - Machinist - $34.68

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Troubleshoot and plan different jobs for Machine Shop
  • Ability to program CNC machine and set up for tests
  • Solicit and organize items necessary for supervisor to generate quote and purchase order request form
  • Solicit quotes for part and equipment from vendors
  • All skill requirements listed in Maintenance Tech IV and III – Machinist
  • Lead, follow, read and record work orders via Asset Essentials electronically
  • Record parts utilized, man hours per unit, and communicate information to supervisor

Test Requirements:

  • Complete tests required for Maintenance Tech IV, III, & II – Machinist
  • Create a quote and fill out a purchase order request form

Tool List Requirements:

  • 1-2-3 blocks
  • 3 wire set
  • Jack screw set
  • Back plunging indicator
  • 3/8” or 1/2” impact
  • 1/2” drill
  • Dremel
  • Angle finder
  • Possess all tools on Maintenance Tech IV, III, & II – Machinist list and be knowledgeable in their use

Maintenance Technician IV - Instrument Tech - $24.48

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Has a basic understanding of control circuits, PLCs, and computer software
  • Proficient in repairs on valves, solenoids, and transducers

Test Requirements:

  • Pass written Maintenance Tech IV – Instrument Tech test with a score of at least 50%

Tool List Requirements:

  • Adjustable slip joint pliers
  • Adjustable wrench
  • Allen wrench set SAE and Metric
  • Screwdriver set
  • Tape measure
  • Torpedo level
  • Basic wrench set SAE & Metric
  • Wire strippers
  • 600V rated true RMS multimeter
  • Flashlight

Maintenance Technician III - Instrument Tech - $28.56

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Successful completion of all requirements of Maintenance Tech IV – Instrument Tech
  • Proficient in calibration of transmitters
  • Understands electrical signal and pneumatic control loops

Test Requirements:

  • Pass written Maintenance Tech III – Instrument Tech with a score of at least 60%

Tool List Requirements:

  • Hacksaw or equivalent
  • Screwdriver/nutdriver bit set
  • Side cutting pliers
  • Needle nose pliers
  • Possess all tools on Maintenance Tech IV – Instrument Technician list and be knowledgeable in their use

Maintenance Technician II - Instrument Tech - $31.62

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Successful completion of all requirements of Maintenance Tech IV & III – Instrument Tech
  • Can define and program parameters for VFD installs
  • Familiar with PLC rack layout and I/O sheets
  • Willingness to participate in continuous education courses as directed
  • Utilizes Asset Essentials according to job requirements

Test Requirements:

  • Passes the Maintenance Tech II – Instrument Tech test with a score of at least 75%
  • Passes Maintenance Tech II – Instrument Tech skills test
  • Pass hands-on skills test

Tool List Requirements:

  • Tubing cutter
  • Punch set
  • Chisel set
  • 14” pipe wrench minimum
  • Vice grip pliers set
  • Dead blow hammer
  • Hammer
  • Measuring caliper
  • Possess all tools on Maintenance Tech IV & III – Instrument Technician list and be knowledgeable in their use

Maintenance Technician I - Instrument Tech - $34.68

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Successful completion of all requirements of Maintenance Tech II – Instrument Tech
  • Ability to plan/schedule/lead teams for upcoming projects
  • Can identify, troubleshoot, and resolve all instrumentation issues
  • Ability to conduct relative training for other instrument techs
  • Has a basic understanding of single-phase and 3-phase power

Test Requirements:

  • Passes the Maintenance Tech I – Instrument Tech test with a score of at least 85%
  • Passes Maintenance Tech I – Instrument Tech skills test
  • Passes hands-on skills test

Tool List Requirements:

  • Clamp-on or open jaw ammeter
  • Non-contact voltage tester
  • Precision screwdriver set
  • Wire terminal crimping tool
  • Possess all tools on Maintenance Tech IV, III, & II – Instrument Tech list and be knowledgeable on their use

Maintenance Technician IV - Electrician - $24.48

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Has a basic understanding of single-phase and 3-phase power
  • Assists with electrical repairs, conduit runs, and motor repairs

Test Requirements:

  • Passes written Maintenance Tech IV – Electrician test with a score of at least 50%

Tool List Requirements:

  • Adjustable slip joint pliers
  • Adjustable wrench
  • Allen wrench set SAE and Metric
  • Screwdriver set
  • Tape measure
  • Torpedo level
  • Basic wrench set SAE & Metric
  • Wire strippers
  • 600V rated true RMS multimeter
  • Flashlight

Maintenance Technician III - Electrician - $28.56

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Successful completion of all requirements of Maintenance Tech IV – Electrician
  • Proficient in working with 3-phase power and can read electrical drawings

Test Requirements:

  • Pass written Maintenance Tech III – Electrician test with a score of at least 60%

Tool List Requirements:

  • Lineman’s pliers
  • Punch set
  • Chisel set
  • 14” pipe wrench minimum
  • Dead blow hammer
  • Hammer
  • Electricians’ knife
  • Screwdriver/nutdriver bit set
  • Possess all tools on Maintenance Tech IV – Electrician list and be knowledgeable in their use

Maintenance Technician II - Electrician - $31.62

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Successful completion of all requirements of Maintenance Tech IV and III – Electrician
  • Completes continuous education courses as suggested
  • Utilizes Asset Essentials according to job requirements

Test Requirements:

  • Passes Maintenance Tech II – Electrician written test with a score of at least 75%
  • Passes Maintenance Tech II – Electrician skills test
  • Passes Maintenance Tech II – Electrician hands-on test

Tool List Requirements:

  • Measuring caliper
  • Hacksaw or equivalent
  • Side cutting pliers
  • Needle nose pliers
  • Vice grip pliers set
  • Possess all tools on Maintenance Tech IV & III – Electrician list and be knowledgeable in their use

Maintenance Technician I - Electrician - $34.68

General:

  • Employee locks out machinery and identifies all energy per WSC LO/TO program
  • Employee knows and follows basic federal, state, company, and factory safety rules, regulations, policies, and good practices
  • Employee keeps their work area clean and in good order
  • Demonstrates their reliability daily and has a maximum of one attendance point or less
  • Demonstrates GMP practices daily
  • Abides by CBA 4/1/2025 – 3/31/2028

Skill Requirements:

  • Successful completion of all requirements of Maintenance Tech II – Electrician
  • Ability to plan/schedule/lead teams for upcoming projects
  • Can identify, troubleshoot, and resolve any electrical issues
  • Ability to conduct relative training for other electricians
  • Can define and program parameters for VFD installs

Test Requirements:

  • Capable of successfully rebuilding gearboxes
  • Capable of troubleshooting and repairing any type of pump utilized in the factory
  • Capable of troubleshooting and rebuilding any mechanical component in the factory and training others to perform the same
  • Participate in the planning & scheduling of routine and emergency maintenance of all equipment
  • Willing and capable of leading teams for upcoming maintenance projects
  • Passes written Electrician test with a score of at least 85%
  • Pass Maintenance Tech I – Electrician skills test

Tool List Requirements:

  • Clamp-on or open jaw ammeter
  • Non-contact voltage tester
  • Precision screwdriver set
  • Wire terminal crimping tool
  • Possess all tools on Maintenance Tech IV, III, & II – Electrician list and be knowledgeable in their use

Coming Soon

Coming Soon